Karcher Pressure Washer Outlet Connection Cover

Stock Number: ES538457

Manufactured by Karcher

In Stock Available for immediate despatch

Rated 4.8 out of 5 (282 customer reviews)

Read all reviews Write a review

Main product image Enlarge icon enlarge image

Will this part fit my appliance? [?]

Click on your brand to check if this part fits your appliance

Karcher Pressure Washers

Description

Leaky pressure washer?

The usual suspect is one of the elbow connections, especially if your water pressure is also poor. Due to bad weather or lack of use these connectors can split over time. Replace it to help stop leaks and get cleaning with full power again. 

Please note: Does not include the o-ring seal, which can be purchased separately here.

This spare is chassis and serial number dependent for certain models. Please contact our Call Centre with these details so we can check if it's suitable for your machine. Your chassis number should look like: 1.504-604.1, and the serial number is 6 digits long.

How to replace Karcher inlet and outlet connectors

This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.

Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.

More product images

Product Reviews

Rated 4.8 out of 5 (282 customer reviews)
Write a review
  • Poor quality

    • 3.0 out of 5
    • 4.0 out of 5
    • 3.0 out of 5
    • 4.0 out of 5

    By - West yorkshire

    I had to modify this item before I could use it ,when it was manufactured the moulding process left behind excess plastic that I had to sand away,before it could be fitted .
  • First class service

    • 4.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Leicester

    Your contact was most helpful, understood what I required, delivery was on time. Thanks.
  • Good value

    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Runcorn Cheshire

    Thank you for my purchase. It was an easy transaction

Ask & Answer

(13 Questions and 16 Answers) Ask a question
  • Q still have leak in replaced outlet connection 3 Answers

    model 4.99 new out elbow fitted. leaking at point where elbow meets outlet pump. Ordered o ring for it. I have fitted it over the screw fit on the outlet pump. now cannot fit new elbow to pump. cannot insert metwl clamp. Any ideas? Am I puting the o ring in the correct place? Any help appreciated Bob

    By wyrmbk - 06 May 2010

    • A
      As stated above you need a small O ring which doesn't come with espares part (although espares claim it comes woth all seals). I found that when I connected up to the low pressure hose the outlet connection leaked slightly so I wasn't hopeful. However when I switched on the pump the leak got worse for a second then it stopped suddenly - I assume the pressure seated the O ring properly. The sealing method is quite confusing - the outlet connection has an internal tube with an external O ring which looks like it should seal to the inner surface of the pump outlet. However it as actually much too small to do this - presumably it's for use with a different model. Incidently the pressure hose will seal directly to the pump outlet (without using the elbow) and it seals using this type of external O ring. It seems Karchner use some universal parts that seal in different ways on different models.

      By DavidB - 26 April 2011

    • A
      Hi Bob, You need the small 'O' ring which is about the same size as the one on a male garden hose connector. It just sits on the inner pipe. The screw fitting is not actually used with this connector and (I think) was or is for a different machine using the same pump. The big orange DIY store does a pack of 'O' rings in the plumbing section for about £1.99. The one you need is in there - so is the larger one for the Inlet (clear plastic) pipe. That one sits in a groove and is easy to see! Best of luck, CJ

      By CockneyJock - Trowbridge, Wiltshire - 08 June 2010

    • A
      The O ring fits inside the female connection of the pump so that it buts up to the elbow outlet fitting.

      By slopekeys - penkridge - 01 June 2010

  • Q O-ring needed or not ??? 2 Answers

    After replacing this part, anytime I hook up the pressure hose, the pressure forces water out through the other end i.e. metal c-clip end (washer is still off). Is there a seal/o-ring that I am missing at this end ?

    By DUGG - Ireland - 22 March 2010

    • A
      Nearly made the same mistake. Inside there is a small rubber O ring, luckily I saw it when it fell out but could easily have missed it.

      By wheltonpat - Alicante, Spain - 12 May 2010

    • A
      Yes. It is a standard size, Though I cannot remeber the actual size.

      By senna1 - Leeds - 10 May 2010

  • Q our washer keeps running out of water 1 Answer

    there is plenty water pressure at the inlet (3.5bar) can i increase the jet on the float valve at the tank ?

    By chicko - perth scotland - 18 January 2014

    • A
      If the water level is dropping on your machine it is either leaking underneath or perhaps more likely it is syphoning down the drain hose. This can occur if the end of the drain hose is lower than the water level in the machine. To cure this fix the drain hose with the 'crook' to not allow the end to be lower, for more details see our video: http://www.espares.co.uk/advice/7/1732/how-to-diagnose-washing-machine-drain-and-pump-problems

      By Chris eSpares Staff - 20 January 2014

  • Q Pressure Washer Outlet Connector leaks when I turn on the pump 1 Answer

    hi i have just fitted a new pressure washer oulet connector, fitted quite easily, but when i switch on the pump it leaks, but when i turn the pump off and allow the water to flow through it doesnt leak, o ring is in place too, any suggestions please

    By mark - Cheshire - 29 March 2011

    • A
      Hi mark, it may well be that the pump itself has become damaged or cracked - especially if the symptoms started since you started using your washer again after the winter months. Water freezing inside the pump can cause damage and leaks.

      By Rory eSpares Staff - 29 March 2011

  • Q does this part seal to the machine with an o ring? 1 Answer

    Karcher KB5050 needs this outlet part, it has split. There is no O ring on my machine sealing the part onto the machine, should it have one? is the seal integral to the part and machine without an o ring seal. The O ring seal you mention as not provided, is that only an O ring seal for the outlet hose to this part? Please confirm before i order.

    By Petrolhead63 - 20 January 2010

    • A
      It certainly needs a ring, but the original ring could be stuck in the socket into which the part fits

      By Greybeard0151 - Chester - 25 February 2010