Cooker not heating up as normal? Get your buns baking again with this replacement circular main oven element from Electrolux.
Please note: This part is PNC number dependent for some models. Please contact us prior to ordering to ensure this is the correct part for your model.
Genuine spare part for select AEG, Blanco, Electra, Electrolux, Fagor, Firenzi, John Lewis, Moffat, Parkinson Cowan, Tricity Bendix and Zanussi cookers. Please see the list of compatible appliance models prior to purchase.
Other part numbers for this item: 3110231002, 3110231010, 3113638005, ES139467, TY14124
How to replace an oven element
This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.
Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.
QWill this stop my electrics tripping out when I turn the oven on?5 Answers
Main oven has started tripping my electrics. Grill and top oven all ok. But as soon as the main oven is turned the power trips out.
- 29 December 2008
your element has shorted to earth replace element
By handyman017- scarborough
- 12 March 2010
its the main cooker element has blown,so triping out,i had exactly the same,fitted new one now better than before
By Anonymous- ashford
- 04 March 2010
yes it should do. when an element goes it melts together and it could cause a short circuit other causes could be loose wiring on element
By Anonymous- essex
- 24 February 2010
It is possible that the main element has been damaged and it is causing an electrical short. Sometime the circular rigns fuse together and that may cause the short.
By sigmosh- London
- 23 February 2010
Without actually seeing your oven, it is impossible to tell what is causing this problem. What I would advise is talking to your local cooker specialist and they should be able to diagnose the problem for you. And that's where we come in! With thousands of oven spares, we're bound to have the part for you.
QMy oven has a top oven and a bottom oven. Which one is this element for? (I need one for the bottom oven!)4 Answers
By nyoung02- Wiltshire
- 29 April 2010
This element is for the BOTTOM OVEN of a Zanussi ZHQ575. To replace, gently unclip the thermostat from the top right hand corner of the back plate, unscrew the back plate and old element, pull the spade connectors from the element taking care that the wires don't spring back into the holes. Push the connectors on to the new element and reattach the element and backplate to the cooker. Clip the thermostat back in place. Should take no more than about half an hour.
By unclekev- Southern Ireland
- 16 February 2011
Please contact us with your full model details so that we can help you get the correct element for your appliance. Hopefully this link helps:
- 18 June 2010
normally the top oven doesnt have a fan,the only element is for the grill.you can tell if that is working ,by turnig on and see it glowing ,therefore element would be in the bottom oven.but have you checked your thermostat! my advice is do the element first ,as these normally go first,they are very easy to fit ,and dont take much time at all. hope this helps.
By bacardi1- hampshire
- 15 June 2010
This is definitely the one! You just unscrew the plate at the back and the old element, then pull the crimped wires off (this is the hardest bit - I used pliers) then reassemble.
If the lights all come on and it doesnt warm up then its definitely the element!
QIt says I need top check the pnc number against the 'list of appliances' but where is the list of appliances? Could not find on the page,nor found with search..can you confirm which I need - details below...1 Answer
John Lewis oven model JLBIDOS904
Product number 944171399
Serial number 64900009
By Nigel.- Southampton
- 08 February 2012
The element you need for that model and product number is our stock code ES1007939
QArrived in no time but can unscrew the front panel :-(((1 Answer
I have tried all morning to unscrew the front panel to access the element
I have tried WD40 and a lot of it but the screw are so stuck.
Did you ever came across with this before? Do you have any suggestion?
I really want to try to save some money and do it myself
By Gianni- London
- 29 October 2011
I had a similar issue but with just 1 screw on my front panel. It has corroded into the clip at the back and in my effort to unscrew it the cross head just rounded out.
I used a dremil to cut the head of the screw into a flat so i could use a flat blade screw driver. After a bit of wigling about the screw came out and i replaced it with a new one.
QI've changed the main fan element and fan, still not working!?1 Answer
I've changed the fan and element. The old element was open circuit, the new one had a reading of 22 ohms.
So I believe the element went and took out the 32amp breaker in the fuse board.
Is there something else that might have blown at the same time? or a reset device?
By Robsparky99- Letchworth, Hertfordshire
- 01 October 2011
USE A TEST METER FOR TESTING THE POWER AT THE TERMINALS
BE VERY CAREFUL THE WHOLE THING WILL BE LIVE.