Bosch Tumble Dryer Thermostat for WTE6920GB/01

Stock Number: ES111441

Manufactured by Bosch

Only 8 left in stock Available for immediate despatch

Rated 5.0 out of 5 (4 customers)

Read all reviews Write a review

Main product image Enlarge icon enlarge image

Will this part fit my appliance? [?]

This part is compatible with Bosch WTE6920GB/01 Tumble Dryers

Not what you're looking for? See all parts for your appliance.

You can also check compatiblity with other Bosch Tumble Dryers

Description

Replacement thermostat to control the temperature within your tumble dryer to an accurate degree.

Genuine spare part for select Bosch, Neff & Siemens tumble dryers.

This is Bosch spares reference: 154166

More product images

Product Reviews

Rated 5.0 out of 5 (4 customers)
Write a review
  • Saved loads of Money

    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Leicester

    This Thermostat saved me the cost of a new tumble dryer.. Even had an engineer out who said nothing wrong with dryer.. But as i knew it wasnt drying correctly i presumed it would be this part as both element were ok. Had to remove top of dryer and side panel, to gain access to thermostat which was located just inside the door through the vents.. Push the old thermostat out with a piece of wood ( held in by rubber gromet) disconnected old one, removed grommet added new one and reconnected and push back inplace from insde machine.. Dryer is now working 100%!
  • Just excellent, no more no less

    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Dorset

    They sent me the exact replacement within 36 hrs of ordering it. Tumble drier fixed, just a pity the postage was so expensive!
  • Now the clothes dry.

    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Pembrokeshire

    Dryer would heat and rotate but not dry fully. I took a guess that this would fix it, it did. To fit remove the top and right hand side . Working through the door opening push on top of the sensor with a length of wood to remove it. From the right side unplug sensor and remove from grommet. Replace the grommet in machine. Connect new sensor, put some liquid soap around the top shoulder and push it in place. Replace side and top. Good as new.

Ask & Answer

(9 Questions and 6 Answers) Ask a question
  • Q WTE84307GB Bosch Exxcel Condenser Dryer too hot 1 Answer

    Please could you advise if the thermostat is likely to be the problem with our Bosch Exxcel Tumble Dryer, (I have checked and this is the correct spare part for our model). It heats up and dries the clothes effectively but even on the "low heat" setting, it is very hot and has therefore been shrinking our clothes! We have been through your video clip on heating issues with tumble dryers and already cleaned and emptied out the filters and water containers. Thanks!

    By MammyVeg - 24 August 2014

    • A
      Check your wash care labels to confirm that these clothes are OK for tumble drying. If the dryer is clear of blockages and vents OK then a new thermostat may improve this however you may still experience shrinking with some clothing.

      By Chris eSpares Staff - 26 August 2014

  • Q Hi My Bosch WTL 6305GB Dryer does not heat up. 1 Answer

    The heating unit has been replaced but still does not heat up. I have removed the above thermostat and a test meter indicates it is open. What is the normal state of a good working thermostat? Before I purchase a new thermostat from you I want to confirm that I have identified the faulty part. Many thanks.

    By Jim - Auckland New Zealand - 20 May 2014

    • A
      This in my opinion looks more like a typical thermistor. If this is the case it could have a resistance of between 2000 ohms and 40,000 ohms. if you can read a resistance between these values it is likely to be correct. If it is a condenser dryer check that it does not have a float valve turning the heater off when the water is full.

      By Chris eSpares Staff - 20 May 2014

  • Q I have changed the heater element, but still no heat, how do I know if the thermostat is faulty, what should the resistance readings be for hot, warm and cold? 1 Answer

    I have checked the sump pump and it is running, everything else has been cleaned.

    By Anonymous - 12 March 2011

    • A
      Hi there. The first thing you need to do is make sure your multimeter is set to the 'ohms' function and the range is set to the lowest ohms range. Attach the multimeter test leads to the connection terminals on the thermostat. For a fully working thermostat with an open circuit, the LCD should read 'OL', '0.00' or '0.5'. If it's a number higher than 0.5, the thermostat will need to be replaced.

      By Rory eSpares Staff - 24 March 2011

  • Q r4381x1gb/01 is not blowing hot/warm air. all filers are clean and i have replaced the heater unit (stupidly). max heat which can be achied is to iron dry indicator. Could this be due to thermostat stock no.ES111441. very minor warm achieved, hardly detec 1 Answer

    What a great and very useful site you run.

    By Veseyan6 - Birmingham - 18 December 2010

  • Q does this control the heater for the dryer? 1 Answer

    model wtl6106gb/07. I recently replaced the heater element but still not working properly. Is this easy to fit?

    By hondacivic - dublin - 03 July 2009

    • A
      Hi Hondacivic, this thermostat monitors temperature in the dryer - it ensures that the element is heating to the correct temperature. As for fitting it, I wouldn't attempt it if you weren't 100% confident. The stat sits at the bottom right in the frame where you enter the clothes.

      By Rory eSpares Staff - 17 March 2010