Bosch E14 Clear Oven Lamp & Removal Tool Assembly - 40W Stock Number: ES539651

Overall rating

• Andrew Leeds,
  4.0 out of 5

  Oven lamp and housing for neff cooker 29 July 2016

  Fitting was not as easy as hoped due to the electrical tags being upright instead of sideways as on the original. I overcame this and new part is fitted and in use.

  Ease of fitting	3.0 out of 5
  Quality	4.0 out of 5
  Value	4.0 out of 5

• TimA Kent
  4.0 out of 5

  Does the job 01 November 2014

  The part comes complete with new bulb, glass cover and plastic glass cover removal tool. A bit fiddly to fit but easy enough once you have taken enough panels off the oven. The new fitting just pushes into place once the old one has been pushed out. Take a photo of the wiring before you pull off the spade connectors so you know the correct connections when you put it back. The replacement fitting needed to have the connectors carefully bent down so it fitted inside the casing. I was worried they might break off but they were fine. There is a terminal block that needs to be unbolted and fitted back on the new fitting but done easily enough with needle nosed pliers. You will need a T25 torx key to unbolt all the oven casing panels, they are not standard cross head screws. Good luck!

  Ease of fitting	3.0 out of 5
  Quality	4.0 out of 5
  Value	3.0 out of 5

• Do not have one Kent
  4.0 out of 5

  Fulfilment 19 December 2013

  The order was delivered within 48 Hours and is now installed and working fine. Quality seems good, after all it is a branded product and very similar to the one it replaced

  Ease of fitting	3.0 out of 5
  Quality	4.0 out of 5
  Value	3.0 out of 5

• Helpful Dad Hertford
  4.0 out of 5

  Improved design on the original - but some problems in fitting 07 October 2013

  I undertook to replace this part in a Neff oven for my daughter. The original had been damaged - the ceramic lamp holder was broken. The excellent e-Spares video is sadly no help as it only explains how to remove the glass and fit a new bulb. The holder is held in by clips which spring out when it is fitted, so removing the old one is a challenge (in my case solved by the use of surgical forceps - but not everyone has those!) Then there was the problem of the connections. There are the normal live, neutral and earth spade connectors - removing them also required the above mentioned forceps. In addition there was a block with three wires, attached to the rim of the lamp-holder by a tiny threaded stud with a shake-proof washer and a nut. The wires were very short and the mounting was vertical. It was impossible to remove the connectors, so the block was removed by taking off the nut. Replacing the same on the new fitting was the real challenge, eventually accomplished before pushing the other connectors on and clipping the lamp-holder in place in the top of the oven - permanently - it can really only be removed again if it needs to be replaced!

  Ease of fitting	3.0 out of 5
  Quality	4.0 out of 5
  Value	4.0 out of 5

• Geoffo Sheffield
  4.0 out of 5

  Reset the clock on at least some Neff ovens before testing! 20 May 2013

  Bought this, arived promptly and fitted without too much difficulty (just a bit fiddly), but the light didn't come on. Checked all the contacts etc, and in the end called out a local service company. They set the clock and it works! (Fortunately they didn't charge a full call out). So after fitting make sure you set the clock before testing the light.

  Quality	5.0 out of 5
  Value	5.0 out of 5
  Ease of fitting	4.0 out of 5

• Anonymous Lewes
  4.0 out of 5

  Can't be faulted 20 April 2013

  I only really wanted the glass cover but I could not find that as a separate item. The bulb will no doubt be useful in the future, with luck I shall never have to replace fitting itself. The glass removal tool is perfect, I already had one but having two increases my chance of finding one when I need it!

  Quality	5.0 out of 5
  Value	3.0 out of 5
  Ease of fitting	5.0 out of 5