Get The App From Play Store!

Skip to main content

Tumble Dryer Thermostat Kit Stock Number: ES487865

Genuine spare part for select Ariston, Creda, Crusader, Electra, Hotpoint, Indesit, Jackson and Proline tumble dryers

Product Q&A

Ask a Question

I've checked the parts were suitable, rechecked the installation but I'm still not getting heat. What could be the solution?

By Raye0524 - Cardiff - 29 April 2012
  • Caitlin from eSpares
    Caitlin at eSpares says...

    Considering you've replaced both above parts it could be a fault with the timer. This would need to be looked at by an engineer though as further self diagnosis can be difficult.

Answer this question

I have replaced both the thermostat and heating element but dryer still blowing cold air only - any other solution - help!

By Debs - London - 14 February 2012
  • Just make sure the stats are round the correct way and put them on a test machine to see if a current is passing through (good electrical hardware would help). They could be faulty. By Tim - - 19 March 2012
Answer this question

Model No;37667 Serial No; 77 101 655

By buster - dumfries - 28 November 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi buster, the thermostats are located on the back panel of the dryer next to the element. There may be a cover over the element and 'stats, but this can be removed by unscrewing.

Answer this question

back together it run ok for about half an hour then went cold again so i tested the thermostats and found the grean one had blown why?

By stirl - mansfield notts - 25 August 2010
  • umm not to sure here try replacing the heating elements. not sure if this will fix your problem By ASH - Northamptonshire - 05 January 2011
Answer this question

Just purchased new Thermostat kit for my Crusader 3kg Tumble dryer. Have fitted new items correctly but still blowing cold air. Any ideas please ? Terry Smith

By Anonymous - - 11 May 2010
  • eSparesMalindi from eSpares
    eSparesMalindi at eSpares says...

    Please contact an engineer for help because we cannot give out technical advice unfortunately.

Answer this question
By thumper40 - - 22 March 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi, fitting this thermostat is a tricky job, and I wouldn't attempt it unless you felt extremely competent at this type of fix-it. It involves removing the rear panel of the machine, and disconnecting the old stats. Don't try if you're not 100% confident!

Answer this question
By Anonymous - - 17 February 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi Jason. It sounds as if one of the thermostats has gone. Replacing a thermostat is a tricky job; it involves removing panels from the dryer, really getting stuck in. If you're not confident about knowing your way around the inside of a tumble dryer, I'd call a repair man.

Answer this question

i recently bought a new heater element from yourselves for a hotpoint tcm 65a tumble dryer. one of the elements was broken on the old one.fitted new parts and my dryer is still blowing cold air help,the wife is giving me grief

By carloss - - 13 September 2009
  • maybe your thermostat has gone By dadio34 - west midlands - 01 November 2009
Answer this question
By deling32 - - 08 May 2009
  • Rory from eSpares
    Rory at eSpares says...

    Hi Deling32, check out this page for possible causes and solutions to your problem: http://www.espares.co.uk/advice/tumble-dryers/a/9/117/common-tumble-dryer-faults.html

Answer this question

Will this part fit my appliance?

Check Now

Tumble Dryer Thermostat Kit

£22.99
(inc. VAT)
£22.99