Dishwasher NTC Thermal Sensor Stock Number: ES1603554
Genuine spare part for select models of Beko and Blomberg dishwashers
Purchased in October 2017. It does all the wash cycle and cleaning but after each cycle dose not dry and leaves grease on all iteams. NO heat when I open door. Do I need to replaces thermostat or heat flow element ?. 1 Answer
-
eSpares Staff at eSpares says...
You need to test the components with a multimeter to determine what has failed, we have a video to help diagnose problems www.youtube.com/watch?v=7b1-M_WKYJs&t
Where is this part located on a Beko DSFN1534B? How long is it so that I know roughly what I am looking for? 1 Answer
-
Hamza at eSpares says...
This is a small sensor that fits onto the base of the Sump Assembly which is stock number ES1250243
The heater on my Lamona dishwasher HJA 8630 stays on after the cycle has finished.Is it the thermostat that needs replacing? 1 Answer
-
eSpares Staff at eSpares says...
We have a video on diagnosing heating issues www.youtube.com/watch?v=7b1-M_WKYJs&t just copy and paste into your browser.
I need to replace the thermostat and am looking for a user guide to do so
-
eSpares Staff at eSpares says...
This item is usually located in the base of the dishwasher, we do not currently have a video on the replacement of this part at this time.
I believe I will need a heating element or thermostat for my Beko dishwasher DFS05X10W. Purchased in September 2016. It does the wash cycle and cleaning / drying cycles, but the glasses are cold to touch, wet and no steam or heat coming out when I open door etc. Could you please recommend whether I need a thermostat or heating element or another part to make it in working order. Also I presume I can look on YouTube for one of your videos on how to do the repair? Kind regards
-
Chris at eSpares says...
See our advice centre for more information like 'how to diagnose leaking and heating problems in a dishwasher'
-
Chris at eSpares says...
The thermistor Stock Number ES1603554 is fitted in the sump under the cavity.
Can you tell me where the NTC is located on a Beko DW600? Will I need access to the underside to measure its resistance? 1 Answer
-
Dean at eSpares says...
We believe the NTC is normally located in the base connected to the sump area.
My beko dsfn 1532b is not heating up but the element is fine could this thermostat be the problem if so how could I check ? The thermostat is 41 k ohm is this correct 1 Answer
-
Chris at eSpares says...
This is an NTC so the resistance changes with temperature and is not likely to be the problem. Got to our advice centre for more information on your problem.
My dishwasher seems to be 'staying on' hours after the end of the cycle. When i open the door steam spews out as if it has just finished. Will this part stop the problem? If so, do you have a how to fit video on your site?
-
Dean at eSpares says...
Check the resistance of the NTC before deciding if it’s faulty, if there is no reading it is likely to be faulty, check out our video for more help www.youtube.com/watch?v=7b1-M_WKYJs
My dishwasher is heating up too much and therefore warping some plastic items, would this be the item to fix this? 1 Answer
Our dishwasher has been working fine for 3 years, and all of a sudden, plastic dishwasher proof items are coming out warped. This is due to the dishwasher getting too hot (we use a 50 degrees cycle). This also means that the cycle is overrunning and we have to turn it off manually. But even after a standard 2hr cycle, this has become hot enough to warp some items.
-
Dean at eSpares says...
Check the resistance of the NTC before deciding if it’s faulty, if there is no reading it is likely to be faulty, check out our video for more help www.youtube.com/watch?v=7b1-M_WKYJs
Will this part fit my appliance?
Check Now