Get The App From Play Store!

Skip to main content
  • Over 4 million customers served

    Part assist UK call centre

  • Over 311,000 Reviews!

    Rated 4.7/5

  • 15 million parts delivered

    Next day delivery until 9:00PM

Dishwasher Large Soap Dispenser Lid Assembly Stock Number: ES572972

4.7 out of 5 4.7 out of 5 (11 Reviews)

Dishwasher Large Soap Dispenser Lid Assembly - ES572972

4.7 out of 5 4.7 out of 5 (11 Reviews)

Genuine spare part for select AEG, Electrolux, Faure, Firenzi, John Lewis, Tricity Bendix and Zanussi dishwashers

Read more

Manufactured by Electrolux

(This part fits select models)

Will this part fit my Appliance?

Does it fit?
Enter your model number and select from the below list
Need help finding your appliance model number?

Check this part fits your appliance

2. Enter your model number

Dishwasher Large Soap Dispenser Lid Assembly

If you have accidentally damaged the dispenser lid on your dishwasher, don't worry, eSpares may just have the spare you need. With this replacement soap dispenser lid assembly, you could soon have your dispenser functioning like new again. 

This is a genuine spare part for select AEG, Electrolux, Faure, Firenzi, John Lewis, Tricity Bendix and Zanussi dishwashers.

Please check the suitable model fit list to ensure that this is the correct part for your appliance.

Electrolux spares reference: 4006078028

Write a review

Here’s what other people are saying about Dishwasher Large Soap Dispenser Lid Assembly.

(11 reviews)

4.7 out of 5

Ease of fitting 5 out of 5
Quality 5 out of 5
Value 4 out of 5
  • Trevor Cumbria
    5.0 out of 5

    Original Spare Part 24 September 2020

    Exact match for my dishwasher and original part match. Fitted and working perfectly. Excellent fast trade as always from a trusted seller.

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 5.0 out of 5
  • Richard Chambers Leeds
    4.0 out of 5

    Fitting the lid 08 May 2018

    I nearly did not order the lid (which I definitely needed) because I was worried about how to fit it. How, I wondered, could I fit a new lid if I could not even take the old lid off? I hope these tips, based on my experience, will remove the unfounded fears of other customers. 1. To remove the old (defective and useless) lid, cut it off, as recommended by a contributor in the "Ask and Answer" section of this webpage. I used a pair of standard side-cutters* to cut through a couple of the strengthening ribs near the left-hand stub-axle of the lid. This made the lid sufficiently flexible so that it would bend a bit, allowing the stub-axle to come out of its housing. 2. Fitting the new lid. The lid must be fitted in the open position, just like the old lid was. Start by inserting the right-hand stub-axle into its housing, with the spring in its correct position. Following the suggestion in the "Ask and Answer" section, I heated the new lid in very hot (not boiling) water to make it more flexible, but I found that I still could not get the left-hand stub-axle into its housing. I put one drop (only) of cooking oil onto the stub-axle, to try to make it slide in more easily. That, on its own, still did not work. Then I noticed that there is a very shallow channel, hardly visible, about a quarter of a millimeter deep, on the inside flat face of the left-hand axle-housing. I found that the end of the stub-axle slides easily along this channel, and easily clicks into place. Job done, in 5 minutes total, including sorting out all the difficulties I have described above. With the help of these instructions, anybody else should be able to do the job in about 30 seconds. I did the job only once: when the lid has been fitted, it cannot come out again for a second try. For that reason, I do not know what was the determining factor of my success. It could have been the heating of the lid in hot water, or the one drop of cooking oil, or the groove that I eventually noticed. I recommend all three methods together. * Side-cutters look superficially like pliers, but are not for gripping. They have cutting edges and are normally used for cutting wire and cable. Available in most hardware shops, B&Q, etc

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 3.0 out of 5
  • AC
    5.0 out of 5

    Quality Dishwasher Replacement Part 27 January 2018

    eSpares were one of just a few suppliers who had this Zanussi dishwasher replacement part in stock. The eSpares website is easy to navigate, and the part arrived within 2 working days. Easy to fit - dishwasher working properly again!

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 4.0 out of 5
See all reviews
Ask a Question

1 Question and 1 Answer

It looks like there is a spring loaded end but I don't want to force it and risk breaking the whole dispenser

By Baz - Italy - 10 November 2014
  • Chris from eSpares
    Chris at eSpares says...

    If you are removing a broken door carefully cut it to allow it to lift of the pivots. When fitting the new door soak in hot water for 2 minutes to soften and make more flexible during fitting.

Answer this question

Will this part fit my appliance?

Check Now

eSpares
4_7
See our reviews

Dishwasher Large Soap Dispenser Lid Assembly

£21.72
(inc. VAT)
£21.72