Universal Washing Machine Drain Pump

Stock Number: ES1087464

In Stock Available for immediate despatch

Rated 4.6 out of 5 (395 customers)

Read all reviews Write a review

Main product image Enlarge icon enlarge image

Will this part fit my appliance?

This product is compatible with:

  • Washing Machines - Please See The Product Specifications


High Quality Universal Washing Machine Drain Pump

If the drain pump in your appliance has become faulty or damaged so your machine is no longer draining, then this quality spare is the ideal replacement. You can now help get your appliance back to draining the water away and not leaving water at the bottom of the machine.


  • Type: Askoll M224 XP
  • 220-240V ac
  • Hertz: 50Hz
  • 0.2A
  • Wattage: 40W
  • Comes with 2 x fixing brackets
  • Askoll pump
  • Made in Italy
  • Please Note: This is a universal Drain Pump that fits most washing machines easily, but please check the pump type and power to ensure this part is suitable for your model
  • Manufacturers’ names and numbers are used for reference purposes only. This part is in no way associated with the initial manufacturer's parts

Compatible spare part suitable for most washing machines (check above specification information)

How to Replace the Drain Pump on a Washing Machine (Zanussi, AEG, Electrolux )

This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.

Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.

More product images

Product Reviews

Rated 4.6 out of 5 (395 customers)
Write a review
  • good value

    • 5.0 out of 5
    • 3.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Heathfield, East sussex

    I bought this pump as a replacement on a Siemens washing machine, it looks to be as well made as the original. The only reason I gave it a slightly lower rating on the fitting was because I had to modify it slightly. the original pump just clipped on but I had to drill a couple of lugs on the new one and secure it with screws but otherwise very good.
  • good quality, does job

    • 4.0 out of 5
    • 4.0 out of 5
    • 4.0 out of 5
    • 5.0 out of 5

    By - Staffordshire

    Excellent product, because our washer is 13 years old had to do minor adjustments, works fine
  • Works fine, job done!

    • 5.0 out of 5
    • 4.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Aberdeenshire

    Having found our Zanussi washing machine was failing to drain I used Espares video to help me remove the pump. Note that other videos suggest removal of panels, seals, door lock, etc., just to get at the pump. eSpares video confirmed it should be possible just but carefully turning the machine on it's side. Also our pump is held in place with screws but one on video has a clip mechanism. The pump still turned when powered but, in hindsight, not very fast since it failed to drain the machine on the next run. Quickly found the part on eSpares and it arrived a day or two later. Easily fitted and works a treat. A small bit of the environment saved but my wife is upset that she doesn't get a new washing machine.

Ask & Answer

(45 Questions and 48 Answers) Ask a question
  • Q I have a Zanussi ZWF1221F washing machine which is'nt getting rid of water and after a spin cycle the clothes are still pretty wet. Could it be the pump?. 3 Answers

    By g - Motherwell - 07 November 2014

    • A
      Thanks for rugbyscrumdown input but this is unlikely. A modern machine will not try and spin until the water level has reached empty. If this is not achieved within a few minutes the machine will usually shut down in a 'fault mode' with the remaining water in the drum. This would not just leave damp clothes but water in the drum as you unloaded.

      By Chris eSpares Staff - 12 December 2014

    • A
      possible slight blockage, have you cleaned the filter? If you run the machine on spin only after the end is it still wet? if not it is slightly blocked up, 1/4 packet of household soda crystals on 60 deg wash will sort it out( if you are in a hard water area)

      By rugbyscrumdown - Alton Hants - 11 December 2014

    • A
      If the drum is not full of water it is draining correctly. The most likely cause of your problem is out of balance. For more information see our video: How to Prevent a Washing Machines Spinning Noisily http://www.espares.co.uk/advice/7/2401/how-to-prevent-a-washing-machines-spinning-noisily-

      By Chris eSpares Staff - 07 November 2014



    By ALLY - WORCESTERSHIRE - 07 February 2014

    • A
      My technician recommended running the hottest programme once a week to see off nasty smells. We found a dose of of washing m/c cleaner did the trick

      By Alan - Oxford uk - 04 April 2014

    • A
      The problem with your machine is likely to be a build up of mould and bacteria probably caused by not allowing the drum to dry out between washes. For more information see our video: http://www.espares.co.uk/advice/7/1524/how-to-use-limescale-and-detergent-remover

      By Chris eSpares Staff - 10 February 2014

  • Q How do I stop water draining out of my machine? 2 Answers

    I have a samsung washing machine B1415J. The water comes into the machine and is drained out continuosly without the water pump being on. Also gives an E9 error. Can anyone help Please.

    By Nash - UK - 17 February 2011

    • A
      The machine is syphoning.Check your outlet hose is not rammed down the pipe also check the stand pipe is 18 inches high. The fault code is telling you that the water is being drained from the machine

      By mayday1 - Spain - 25 February 2011

    • A
      H Nash, it sounds as if the problem is with either the sump hose (the hose that drains the drum down to the pump) or the pump. Check both for damage, and replace as necessary.

      By Rory eSpares Staff - 18 February 2011

  • Q How do I replace a motor pump in my washing machine 2 Answers

    I have a Tecnik washing machine model no TKL9060 which due to a short curcuit is now not working properly. An engineer said that it would be too costly to repair as it was a problem with the motor but if I replaced the motor pump would that solve the problem I wonder as all the programmes seem to be there on the control panel but it just makes a low whirring sound with no movement

    By AnnieO - Belfast - 20 January 2011

  • Q I have a waq283s0gb Bosch washing machine and is making lots of noise 1 Answer

    i was told I can't change the drum bearing for this model If yes where can I buy it

    By Ab - London - 20 April 2016

    • A
      The bearings appear to be available for your range of machine but to be certain we would need the model and /?? after the GB.

      By Chris eSpares Staff - 20 April 2016