Skip to main content

Call eSpares 0844 9777 888 (7p per min + any network access charge)

Hoover Tumble Dryer Dryer Element 2100W for HNV160-80 Stock Number: ES1018786

Hoover Tumble Dryer Dryer Element 2100W for HNV160-80 - ES1018786
View video

4.7 out of 5 Rated 4.7 out of 5(3 customers)

Genuine spare part for select Candy and Hoover dryers

Read more

Manufactured by Hoover

Will this part fit my Appliance?

You can also check compatiblity with other Hoover Tumble Dryers below

Need help finding your appliance model number?

Yes

This part is compatible with Hoover HNV160-80 Tumble Dryers.

Not what you're looking for?
See all parts for your appliance.

Tumble Dryer Dryer Element 2100W

If the heater in your tumble dryer has stopped working or isn't as effective as it was when you bought it then eSpares has the perfect spare part for you! This replacement part is sure to get your tumble dryer working like a new machine once more.

It's a genuine spare part for select Candy and Hoover dryers in the list of appliances. Before ordering, please check the model fit list to ensure this part is suitable for your appliance.

Specification:

  • Wattage: 2100W

PLEASE NOTE:This part is now a 3 wire connection and no longer 4 wire and requires an engineer to fit part.

Write a review

Here’s what other people are saying about Hoover Tumble Dryer Dryer Element 2100W for HNV160-80.

(3 reviews)

4.7 out of 5

Ease of fitting 5 out of 5
Quality 4 out of 5
Value 3 out of 5
  • Surrey
    5.0 out of 5

    Did the job

    I used this for a candy tumble dryer which was turning but not heating up. It was really easy to fit, the wires are coloured coded (although mine were faded so needed a torch to make sure I didn't mix it up) I did however drop the wires but managed to get them back by lifting the machine onto it side a bit. Only need a screwdriver over than that. Done in under 20 minutes I'm guessing.

    Quality 5.0 out of 5
    Value 5.0 out of 5
    Ease of fitting 5.0 out of 5
  • Cambridge
    4.0 out of 5

    Replace heater element - Candy Tumble Dryer

    Probably no alternative to buying the original Candy part but is expensive relative to the cost of a new dryer. Took a chance after finding dryer was not generating enough hot air before. In addition, when turning on, all red lights illuminated, dryer started but immediately cut out. Half expected electronic board faulty. Took chance to replace heater element. Part is not pretty but functional, Hidden anyway ! UNPLUG APPLIANCE Having watched E-Spares video I removed top panel to remove side but realised not poss. Chance to see inside & view terminals, circuit board etc. . Removed rear fan/heater cover. Realised terminals would come out one by one using thin nose pliers (pull female connector) through the small hole. From there, 2 screws to remove old heater & replace, make connections, push back through hole. Before replacing top vacuumed out considerable fluff. Job finished. Dryer starts O.K. lights function normally, produces hot air again. Fair expectation drier will give further good service so cost probably justified. Easy DIY fix. Only tools - Philips screwdriver, thin nose pliers (vacuum cleaner - optional !)

    Quality 4.0 out of 5
    Value 2.0 out of 5
    Ease of fitting 5.0 out of 5
  • 5.0 out of 5

    replacement

    heater was a replacement part was easy to fit and now my tumble dryer works

    Quality 5.0 out of 5
    Value 3.0 out of 5
    Ease of fitting 5.0 out of 5