Washing Machine Motor Tacho Coil Stock Number: ES1568233

Overall rating

• Harry Oxford
  5.0 out of 5

  A fix for Electrolux Dishwasher ESL5201LO 06 October 2021

  The heating of our Electrolux Dishwasher ESL5201LO did not work anymore and it only washed cold but finished the cycle. After some fault finding it became apparent that the Tacho Sensor was defect. Unfortunately not available as a individual spare part and only as part of the complete Pump & Heater set. This is a disgrace not only cost wise but even more from an environmental perspective!! After some internet research I found that this Beko Tacho sensor is an exact fit size wise and relatively easy to install (for a competent person). The only downside the resistance of the coil is lower (about 90 Ohms). However the dishwasher does not seem to care about this discrepancy as the heating works again! For me this is a great result! Disclaimer: Any repairs based on this review are at your own risks people!

  Ease of fitting	5.0 out of 5
  Quality	5.0 out of 5
  Value	5.0 out of 5

• Nerijus
  5.0 out of 5

  Fit ror AEG* 08 October 2018

  I had used it for AEG pump. But you need 100 Ohm resistor put (solder) in parallel, becuause AEG tacho coil is 220 Ohm. Coil generated 6V AC. Fit fine, works fine.

  Ease of fitting	5.0 out of 5
  Quality	5.0 out of 5
  Value	5.0 out of 5

• carl birmingham
  5.0 out of 5

  billiant 11 August 2016

  worked a treat, wifes happy so all good didnt take long to arrive and fit, many thanks will be using you again.

  Ease of fitting	5.0 out of 5
  Quality	5.0 out of 5
  Value	5.0 out of 5

• FL Sweden
  5.0 out of 5

  Quick fix for Electrolux Dishwasher ESL64020 18 July 2016

  Perfect replacement part for Electrolux Diswasher ESL64020 washing pump motor. Tacho error on the washing pump stops the water heater. The pump is working flawless so the weak link is the tacho coil. Some mechanical skills required. Had to drill three rivets for the coil holder. Replaced with short self tapping metal screws. Internal resistance of coil is about 92 Ohm.

  Ease of fitting	3.0 out of 5
  Quality	5.0 out of 5
  Value	5.0 out of 5

• Eerik Estonia
  5.0 out of 5

  Also fits dishwashers 08 September 2015

  I installed this in an Electrolux dishwasher which gave an id0 code which meant no tachometer signal. Replacing it was a 10 minute job. Electrolux wanted to replace the whole pump assembly and that would have cost over 200€. This saved me a lot of money. Shipping took around 1,5 weeks to Estonia. For information, this coil has a resistance of around 90 ohms.

  Ease of fitting	5.0 out of 5
  Quality	5.0 out of 5
  Value	5.0 out of 5

• Stefan Sweden
  5.0 out of 5

  Solved my problem perfectly 18 August 2015

  Had a similar issue with my Electrolux Husqvarna QB6260I. Drying sequence failed and reading out the service error code said problems with tacometric generator. Replacement part fitted the pump perfectly and solved my issue and saved me a lot of money.

  Ease of fitting	4.0 out of 5
  Quality	5.0 out of 5
  Value	5.0 out of 5