Get The App From Play Store!

Skip to main content
  • Over 4 million customers served

    Part assist UK call centre

  • Over 321,000 Reviews!

    Rated 4.7/5

  • 15 million parts delivered

    Next day delivery until 9:00PM

Tumble Dryer Square Rear Drum Bearing Stock Number: ES551453

4.7 out of 5 4.7 out of 5 (23 Reviews)

Tumble Dryer Square Rear Drum Bearing - ES551453
View video

4.7 out of 5 4.7 out of 5 (23 Reviews)

Genuine Spare Part for select Ariston, Cannon, Crusader, Electra, English Electric, Hotpoint, Indesit, Jackson, Parnall, Proline and Thorn tumble dryers

Read more

Manufactured by Creda

(This part fits select models)

Will this part fit my Appliance?

Does it fit?
Enter your model number and select from the below list
Need help finding your appliance model number?

Check this part fits your appliance

2. Enter your model number

Tumble Dryer Square Rear Drum Bearing

If your tumble dryer is not turning as it should then it could be that the bearings are faulty, don't worry eSpares could have just the part to get you going again. We have this replacement drum rear square bearing that once fitted to your tumble dryer and you can be sure of getting a better drying performance leaving you with dry clothes again!

This square rear drum bearing is a genuine spare part for select Ariston, Cannon, Crusader, Electra, English Electric, Hotpoint, Indesit, Jackson, Parnall, Proline and Thorn tumble dryers.

Please check the suitable model fit list to ensure that this is the correct part for your appliance. 

Write a review

Here’s what other people are saying about Tumble Dryer Square Rear Drum Bearing.

(23 reviews)

4.7 out of 5

Ease of fitting 4 out of 5
Quality 4 out of 5
Value 4 out of 5
  • Scott London Uk
    5.0 out of 5

    Easy fix for noisy tumble dryer 05 July 2017

    Easy fit, no need to remove drum if shaft is intact just loosen back enough so you can prise the old bearings out. Replace with new bearings let it run for a few minutes and then all the noise hopefully will have gone. Espares where very quick delivery as usual

    Ease of fitting 4.0 out of 5
    Quality 5.0 out of 5
    Value 5.0 out of 5
  • David South Wales
    5.0 out of 5

    DIY Friendly Item 12 August 2016

    Reasonably easy to replace this bearing on my Hotpoint TL21 tumble dryer. You may need to replace the little wire holder securing the bearing washer as it tends to break if yours is an old machine. Job done and squeak gone ( for good hopefully )

    Ease of fitting 4.0 out of 5
    Quality 5.0 out of 5
    Value 4.0 out of 5
  • TT_Gully Up T'North
    5.0 out of 5

    Trying to Solve Dryer Noice 24 October 2015

    Purchased this item to try and solve a "bumping" noise with our tumble dryer. I have replaced this part before (back in 2013) so thought the noise was being caused by it being worn again. I also purchased the pads which locate at the front of the drum. Both were very easy to fit and a great opportunity to vacuum out of the fluff inside the machine Unfortunately once fitted the noise was still there! Checked everything else and all appeared fine. Eventually after a lot of head scratching I found the belt layers had started to separate in one small area. Just looking at the belt it was fine but pulling the belt around the small drive shaft on the motor showed up the de-lamination as it went around the tight bend and formed a lump which is what was making the noise.

    Ease of fitting 4.0 out of 5
    Quality 4.0 out of 5
    Value 4.0 out of 5
See all reviews
Ask a Question

3 Questions and 3 Answers

If so which part do I need we replaced the drum shaft last year my husband has checked and it's not that ?

By debhil95 - - 25 July 2011
  • probably is By gobbilino - Northern Ireland - 07 February 2013
Answer this question

I did not lubricate it since it seems to be graphite and should not need it. Could it have been installed incorrectly? The earth strap has now worn away and needs replacing too although I was surprised at the £7 price tag.

By Kevin - Whitchurch, Hants - 15 April 2011
  • perhaps the surface of the shaft was damaged which caused premature wear By Robw - Surrey - 08 February 2014
Answer this question

It still works, but is very noisy. The sound from the back of the drum varies between a rattling sort of squeak to an ear-splitting squeal - exactly the sound I'd expect from a failed bearing. Is there anything else it might be? And if it is the bearing, how difficult is it to fit - you haven't included this in your "how to" videos.

By Joe F - Thatcham, Berkshire - 25 November 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi Joe F, it does sound like the bearing has gone, and unfortunately replacing bearings is a big job. You'll need to take the back and side panels off the dryer to get access to it. Once you've removed the panels, you should be able to deduce how to get the bearing off. Best of luck!

Answer this question

Will this part fit my appliance?

Check Now

eSpares
4_7
See our reviews

Tumble Dryer Square Rear Drum Bearing

£17.38
(inc. VAT)
£17.38