Skip to main content

Call 0844 9777 888 (7p per min + any network access charge)

Universal Magnetic Fridge Freezer Door Seal -130cm x 70cm Stock Number: ES1539567

Universal Magnetic Fridge Freezer Door Seal -130cm x 70cm - ES1539567
View video

3.4 out of 5 Rated 3.4 out of 5(38 customers)

Compatible spare part for all models of 130cm x 70cm refrigerators

Read more

Universal Fridge Freezer Door Seal - Up to 130cm x 70cm 

If the door seal on your fridge freezer door has worn away or snapped, then most likely the chill will be escaping your appliance. Don't get hot under the collar about it, grab this spare part from eSpares! Here we have a compatible replacement door seal, which will ensure the cold air remains in your fridge freezer not your kitchen!

This is two L shaped moulded seals and two corner connecting pieces.

Simply cut to the length of your seal and glue the two connecting pieces to produce a suitable four sided magnetic door seal.

Specification:

  • Size up to (L) 130 x (W) 70 cm x 12 mm depth (cut to size if smaller)

Please check the dimensions of your refrigerator prior to ordering this part as it size-specific.

Important Information:

This seal is designed for older appliances that have a detachable door liner that is fixed in position by screws.

We suggest only considering using this seal if your original seal is no longer available and the seal fitted is in very poor condition

Attempting to fit on any other type of fridge or freezer may result in the appliance door leaking or being unusable.

Write a review

Here’s what other people are saying about Universal Magnetic Fridge Freezer Door Seal -130cm x 70cm.

(38 reviews)

3.4 out of 5

Ease of fitting 2 out of 5
Quality 4 out of 5
Value 4 out of 5
  • 3.0 out of 5

    Must remember to measure first

    Not long enough for my (very) old freezer my fault for not measuring properly first . Also unable to close the door afterwards . Old seal was a lot thinner seemingly. Possibly too old for parts now

    Ease of fitting 1.0 out of 5
    Quality 5.0 out of 5
    Value 5.0 out of 5
  • Dublin, Ireland
    5.0 out of 5

    Does the job

    Because my freezer doesn't have an off the shelf replacement seal getting a universal seal was the only option. You pretty much have to take the door off the freezer to replace the seal. I used the time to defrost the freezer. I had to cut loads off them as they are for a much larger freezer. I used 5 minute two-part epoxy to glue the corners. I had to hold the edges in place while the glue set so I did one corner at a time.

    Ease of fitting 3.0 out of 5
    Quality 5.0 out of 5
    Value 4.0 out of 5
  • 2.0 out of 5

    No fitting instructions

    The product was compatible with my fridge door, however, there was no instructions with item. The video shows the fitting of a branded seal which seems to just click in place. I have noted in the comments section that others have had the same issue but eSpares have not addressed this problem. All it would take is either a photocopy of the fitting instructions with each purchase or a new video. Hope you take this comment as an opportunity for continuous improvement

    Ease of fitting 2.0 out of 5
    Quality 2.0 out of 5
    Value 3.0 out of 5
See all reviews
Ask a Question

31 Questions and 30 Answers

Dimensions are approx. 60 cm x 60 cm

By Dave - Cheltenham - 17 November 2017
  • Chris from eSpares
    Chris at eSpares says...

    We have no information as to whether this seal can be fitted successfully on your appliance.

Answer this question

Please advise on the necessary cleaning & preparation required & the type of glue needed to successfully glue the corners of the universal fridge door seals reliably. Clearly state the cleaning products which will provide a secure adhesive key for the glue and the order in which the corner seal faces are attached in order to produce a fully airtight joint. I have already attempted to use super glue without any lasting success.

By J Gough. - Shropshire - 15 November 2017
  • Chris from eSpares
    Chris at eSpares says...

    We believe the best results will be obtained with a flexible product such as Evostic contact adhesive or a silicone sealant.

Answer this question

I have fitted the universal door seal. Unfortunately I couldn't find the video but worked out how to tuck it in behind. I haven't done any glueing yet but I have shut the door and particularly in the corners it is not sealing when the door is shut? Do you have any advice

By Ian M - Devon, UK - 25 October 2017
  • Chris from eSpares
    Chris at eSpares says...

    Try warming the seal with a hair dryer to soften and reshape it. This will 'set' once left to cool.

Answer this question

What glue should be used to glue the strip corners together? Where should the glue be applied to ensure the cut corners are attached together providing an air-tight connection? I can't imagine how this is done. Should the corners be glued together whilst the strips are attached to the fridge, or before attaching to the fridge? Thanks

By PB - London - 10 August 2017
  • Chris from eSpares
    Chris at eSpares says...

    The corner fixings can be glued with a contact type adhesive. If cut correctly there will only be a very small gap that should not result in a significant leak. This could be improved by using silicone sealant on the corners being joined.

Answer this question

WHIRLPOOL ARG992K/K/G/R -GB

By L.M.BALL - teesside - 02 March 2017
  • Chris from eSpares
    Chris at eSpares says...

    Although it may be possible to use this Stock Number ES499835 will fit your appliance.

Answer this question
See all questions and answers
Order within 8:30PM for UK Next Day Delivery