Panasonic Microwave Turntable Motor for NNA873S Stock Number: ES132365
Genuine spare part for select models of Panasonic microwaves
The plate covering the turntable motor is fixed all the way round and is actually joined to the back. The plate would be easy to get off by breaking the areas where it is sealed but how can I fix it back on again please? There are no screws. 2 Answers
I have a Panasonic NN A574SB Quartz Grill Combi Microwave Oven Stainless Steel 271 1000W
- The electrical shielding offered by this plate is critical to safety - mircowaves heat flesh as well as food, so know the risk before proceeding. Search YouTube which has plenty of guiding videos. The design is such that you need to snip the thin metal between the holes at the perimiter of the plate in order to remove it. It goes back rotated 180 degrees with tabs locating on one side and use a self-tapping screw on the other side.
- I only broke 3/4 of the tabs and used the others as a hinge. refix by hinging down and bend tabs to hold in place. if not use some duct tape
Is this item compatible with all Panasonic Microwaves? And how easy is this to install? Thanks! 2 Answers
- ia this motor with panasonic model nn-a574
- Don't know whether it is OK for all Panasonic's but would guess it probably is. Easy to install once you have worked out how.
-
eSpares Staff at eSpares says...
You have to use the correct part and rating for the model.
Turntable problem with Panasonic NN-K655BBPQ. Motor is out from underneath, no problem. But coupler from inside unit does not lift up, however hard I pull. Is there a trick to this? I want to inspect it before deciding what the problem might be. 1 Answer
-
Chris at eSpares says...
The coupler should be released once the motor is out as it needs to move slightly 'off center' but will be held by the motor shaft.
I have taken out the microwave turntable motor and disconnected the wires. It has a yellow and a brown wire. How do I know which wire to fit to which connector on the new motor as there are no markings? 1 Answer
-
Chris at eSpares says...
As this is an AC motor the wires can be reversed on the motor without issue. Some motors will rotate clockwise and when stopped may run anti clockwise.
I have accessed the motor from the cover panel under the microwave. All seemed straight forward until I started to try and remove the screws that hold the motor in place. The screws turn and turn and turn but are not releasing the motor. Any suggestions?
-
Chris at eSpares says...
The screws are not the best quality and if over tightened when fitting will have probably stripped the thread on the cavity or screw. To remove use one screwdriver to apply pressure levering the motor away as you unscrew the screws. Once started the screws will often 'bite' and start to unscrew.
microwave is all operating but turntable not turning,have removed table motor and checked continuity across terminalsl with meter but get no reading,so assume motor at fault,although spindal will turn. 1 Answer
-
Chris at eSpares says...
The motor has a high resistance and will not show if you are measuring on a low resistance range use the higher resistance ranges. It also has a high gear ratio drive so should be difficult to turn. Check the coupling to the turntable is not cracked allowing it to slip when driven, see our article: How to replace a turntable motor www.espares.co.uk/advice/5/147
we are using this motor to power a small turntable in a display not in a microwave thank you
-
Chris at eSpares says...
For a 'project' like this i would simply solder the wires directly onto the motor. The small 'spade terminals' may be difficult to obtain but you could try a car spares supplier.
Both motors seem similar, with the same spec. there is a huge difference in price!
-
Chris at eSpares says...
The motors may be Identical but we have no way of knowing. We would recommend using the correct motor if in doubt.
Hi, does anyone know the expected resistance of the motor. I am getting 2Mohm so I believe this motor is faulty but I just wanted to check before ordering 1 Answer
Motor is TYJ50-8A7 synchronous motor 4W
-
Chris at eSpares says...
The motor should be between 12 and 20 k ohms typically so your motor appears to have failed.
Will this part fit my appliance?
Check Now