Candy Washing Machine Drain Pump (Round Top Screw On) : Askoll M231 XP (M224 XP) Stock Number: ES1087464
Fits most washing machines matching the specifications, please check before ordering
I have a Zanussi ZWF1221F washing machine which is'nt getting rid of water and after a spin cycle the clothes are still pretty wet. Could it be the pump?. 3 Answers
-
Chris at eSpares says...
Thanks for rugbyscrumdown input but this is unlikely. A modern machine will not try and spin until the water level has reached empty. If this is not achieved within a few minutes the machine will usually shut down in a 'fault mode' with the remaining water in the drum. This would not just leave damp clothes but water in the drum as you unloaded.
- possible slight blockage, have you cleaned the filter? If you run the machine on spin only after the end is it still wet? if not it is slightly blocked up, 1/4 packet of household soda crystals on 60 deg wash will sort it out( if you are in a hard water area)
-
Chris at eSpares says...
If the drum is not full of water it is draining correctly. The most likely cause of your problem is out of balance. For more information see our video: How to Prevent a Washing Machines Spinning Noisily http://www.espares.co.uk/advice/7/2401/how-to-prevent-a-washing-machines-spinning-noisily-
water is not draining from the machine is this the part i need & is it compatible with model hoover HNL842-80 2 Answers
-
Kas at eSpares says...
there's a possibility of something being stuck in your drain pipe or pump check to see if there is ant blockage. If you find that nothing is causing the drain pipe or pump to be blocked then yes you will require a new pump. The drain pump above maybe suitable for your model, we recommend you check the specifications in the description.
-
Parminder at eSpares says...
This pump is universal and does not have any direct model associations. Please check the pump type and specifications to ensure a correct fit. Please view our advice centre page which will give you more information on draining problems http://www.espares.co.uk/advice/7/1732 The model in this video may be different to yours, however the process should be similar for other makes and models.
hI i HAVE A WHIRLPOOL WASHER MODEL AWO/6728 AND RECENTLY WE HAVE NOTICED A FAUSTY SMELL OF STALE WATER COMING FROM THE MACHINE ALSO THE WASHING ON A 1400 SPIN DOES NOT SEEM AS DRY AS IT USED TO BE?????? MANY THANKS FOR ANY HELP ON THIS..
- My technician recommended running the hottest programme once a week to see off nasty smells. We found a dose of of washing m/c cleaner did the trick
-
Chris at eSpares says...
The problem with your machine is likely to be a build up of mould and bacteria probably caused by not allowing the drum to dry out between washes. For more information see our video: http://www.espares.co.uk/advice/7/1524/how-to-use-limescale-and-detergent-remover
I have a samsung washing machine B1415J. The water comes into the machine and is drained out continuosly without the water pump being on. Also gives an E9 error. Can anyone help Please.
- The machine is syphoning.Check your outlet hose is not rammed down the pipe also check the stand pipe is 18 inches high. The fault code is telling you that the water is being drained from the machine
-
Rory at eSpares says...
H Nash, it sounds as if the problem is with either the sump hose (the hose that drains the drum down to the pump) or the pump. Check both for damage, and replace as necessary.
I have a Tecnik washing machine model no TKL9060 which due to a short curcuit is now not working properly. An engineer said that it would be too costly to repair as it was a problem with the motor but if I replaced the motor pump would that solve the problem I wonder as all the programmes seem to be there on the control panel but it just makes a low whirring sound with no movement
- OK,when an engineer talks about a motor he means the main motor NOT the pump.Main motors tend to be very expensive to replace.Replacing the pump will make no difference.
-
Rory at eSpares says...
Hi AnnieO, check out this video for help replacing the pump in your washer: http://www.espares.co.uk/advice/washing-machines/a/7/1373/how-to-replace-the-pump-on-a-washing-machine-.html. The model in the video is different to yours, but the process will be pretty similar.
Hi ... My zanussi zwt71201wa has developed an E20 error... but was still draining. It only did it during a full was cycle. A drain or spin cycle wouldn't get the error. It was draining ... into a sink It now won't start a program. Is this likelly a pump fault? Or sensor?
-
Dean at eSpares says...
Please see our advice article for help www.espares.co.uk/advice/careandmaintenance/zanussi-washing-machine-error-fault-codes just copy and paste into your browser.
My Zanussi Washing Machine Z949T will not start up when I set the programme switch to any of the wash cycles.The machine only operates when I set the spin cycle 1 Answer
-
Dean at eSpares says...
Check the fill valve as this should operate when turned on the wash cycles.
Hi there your video for replacing the drain pump on a zanussi is very clear. I bought a new pump from espares this week but my machine has a plastic cover on the Base which I can't remove.. any quick tips? 1 Answer
-
Chris at eSpares says...
If the cover is a light weight plastic panel it will usually be held by two or three plastic plugs that can be prised out. Then the panel can be slid to one side and released.
i was told I can't change the drum bearing for this model If yes where can I buy it
-
Chris at eSpares says...
The bearings appear to be available for your range of machine but to be certain we would need the model and /?? after the GB.
Washing machine won't drain at the beginning of cycle like always does, makes a sort of humming noise and then shows error code, filter checked and emptied and still not working. Is this likely to be a new pump needed?
-
Chris at eSpares says...
For information to diagnose your problem see our video: How to diagnose washing machine drain and pump problems: www.espares.co.uk/advice/7/1732