Skip to main content

Call 0844 9777 888 (7p per min + any network access charge)

Heat Resistant Glass Sealant - 310ml for APM6517 Stock Number: ES914819

Heat Resistant Glass Sealant - 310ml for APM6517 - ES914819

4.7 out of 5 Rated 4.7 out of 5(141 customers)

High performance, heat resistant silicon sealant for repairing oven glass and door fixings.

Read more

Will this part fit my Appliance?

This product is compatible with:

  • Cookers & Hobs

Heat Resistant Glass Sealant - 310ml

This quick curing silicone sealant is temperature resistant up to 300 degrees and can be used as a gasket seal in boilers, ovens, ducting, flue and heating applications. Perfect for sticking on an oven door seal.

Specification:

  • Excellent adhesion to most non-porous surfaces
  • Sticks best to aluminium, ceramics and metals
  • Suitable for exterior and interior use
  • Fast cure - tack free in one hour
  • Permanent flexibility
  • 25 years life expectancy

 

Areas of use: For joints and assemblies which must be resistant to high temperatures in ducting, metal chimneys, industrial/domestic ovens, heating appliances.

Write a review

Here’s what other people are saying about Heat Resistant Glass Sealant - 310ml for APM6517.

(141 reviews)

4.7 out of 5

Ease of fitting 4 out of 5
Quality 5 out of 5
Value 4 out of 5
  • Nuneaton
    5.0 out of 5

    This is a first class item

    After fitting 4 rubber seals with out any success I tried the sealant. it was easier to use than the rubber and as done the job.

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 5.0 out of 5
  • Scotland
    5.0 out of 5

    Good Sealant

    Needed to seal two ovens whose rubber seals had stretched and this product was well up to the task. I would recommend this product to be used wherever a hot seal is required.

    Ease of fitting 4.0 out of 5
    Quality 5.0 out of 5
    Value 4.0 out of 5
  • buckinghamshire
    5.0 out of 5

    excellent product

    This product worked perfectly and in my case was to glue a oven glass inner panel back into its rebated steel door. As with any silicone its important to prepare the surfaces and to work as clean as possible since it can be a messy application process if you get it all over your hands. After the nominal cold curing time, the oven was set to 150 deg, then 300 deg and all has remained well. The first couple of uses produced a smell which soon goes. I have since used the product on other applications of general DIY nature with good success.

    Ease of fitting 4.0 out of 5
    Quality 5.0 out of 5
    Value 5.0 out of 5
See all reviews
Ask a Question

25 Questions and 33 Answers

By rich6 - - 29 September 2009
  • If it was originally glued on and not screwed then this will do the job perfectly. You need to leave it a few hours (eg overnight) to set fully before use. By hemlock1961 - East Sussex - 13 February 2010
  • In my opinion yes, but even if it doesn't it won't cost the earth to find out. I say give it a go! good luck. By femfixit - Essex - 11 November 2009
Answer this question

Our 10+ year old oven's plastic door handle has become detached, evidently because the metal screws holding it to the door's metal frame no longer engage with their holes in the plastic handle (the holes must have lost some thread). Some screws holding the oven frame in a chipboard surround are spinning in a similar way, although I don't think they affect functionality (it seems solid enough). I thought about repairing both with superglue, but read that PVA can produce cyanide gas at temperatures above 230C so this seems rather risky. As Heat Mate is OK to 300C, is it the best product to fix the various screws in place, or is some other adhesive/sealant better?

By Ozaru - - 01 September 2009
  • Have you tried different bolts, either longer ones of the same size to use the thread further in the handle, or bigger ones and rethread the plastic of the handle. This stuff probably would do the job but it is a big cartridge and you would only need a small amount. The holes in the chipboard you could pack out with matchsticks (remove the heads obviously). Works as a sort of DIY rawlplug. By hemlock1961 - East Sussex - 13 February 2010
  • Answering my own query after waiting in vain for anyone else to do so... and after hitting upon the revolutionary idea of calling the manufacturer (doh!)... Their technical services department were very helpful, and said (a) the sealant is not 'structural' so might pull straight out again if subjected to any significant load; (b) two-part epoxy resin adhesives (araldite etc.) are fine at high temperatures and stronger than sealants, so that's what I need. There were incidentally other problems I noticed from the docs on the EverBuild website and they confirmed, e.g. 'minimum width 6mm', 'do not use on soft metals such as brass', etc. By Ozaru - - 15 September 2009
Answer this question
By Anonymous - Watford - 10 May 2009
  • You need to scrape the old stuff off and clean off all grease with meths or similar. By hemlock1961 - East Sussex - 13 February 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi Nigelashley, I'd advise removing as much old sealant as possible, as the new sealant will adhere much better to the surface of the oven.

Answer this question
By mums - - 26 February 2009
  • This is what i have used it for and it has worked (so far!) Pretty easy to apply and oven was used the next day By leicesterpie - - 25 May 2010
  • Rory from eSpares
    Rory at eSpares says...

    Hi Mums, this sealant is made just for this purpose - it will re-stick your door glass just like that.

Answer this question
By waterlily - - 16 January 2009
  • yes it works, but is a bit messy, dont spill any By doedoe - liverpool - 20 January 2009
  • Although the oven has only been used twice since applying the new adhesive it seems to have done the job. It was used to re-fix the inner oven glass (NEFF) which had come adrift after 10 years of regular usage. I'm hopeful that it will last at least another 10 years, when it will probably be time for a new one! Beware though, the sealant / adhesive can be very messy to apply if you haven't done it before. Need to spend time to ensure that the old surfaces are thoroughly cleaned up. By Ricardo - South Cumbria - 19 January 2009
Answer this question
See all questions and answers