Skip to main content

Call 0844 9777 888 (7p per min + any network access charge)

Tumble Dryer Rear Drum Bearing for IS70CSK Stock Number: ES865498

Tumble Dryer Rear Drum Bearing for IS70CSK - ES865498
View video

4.8 out of 5 Rated 4.8 out of 5(228 customers)

Spare part for select models of Hotpoint, Indesit, Ariston and Creda tumble dryers

Read more

Will this part fit my Appliance?

Yes

This part is compatible with Indesit IS70CSK Tumble Dryers.

Not what you're looking for?
See all parts for your appliance.

Tumble Dryer Rear Drum Bearing

Your tumble dryer's drum won't be able to tumble properly without all its bearings in good order. Replace a damaged or faulty rear drum bearing with this replacement from eSpares and you can be sure of getting a better drying performance leaving you with dry cloths again!

Specification:

  • Type: Teardrop shape

 

Genuine spare part for select models of Hotpoint, Indesit, Ariston, Proline and Creda tumble dryers.

Please check the list of suitable models to ensure that this spare part will fit your appliance.

Write a review

Here’s what other people are saying about Tumble Dryer Rear Drum Bearing for IS70CSK.

(228 reviews)

4.8 out of 5

Ease of fitting 4 out of 5
Quality 5 out of 5
Value 4 out of 5
  • Carmarthen
    5.0 out of 5

    Did the job nicely

    Good priduct and perfect replacemwnt for tumble dryer bearing that had worn out. Saved a least £150 on what otherwise would have been a manuafurer repair or replacement. Delivered relatively quickly.

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 4.0 out of 5
  • Scotland
    5.0 out of 5

    Essential maintenance item

    This part is one you should keep in stock at home, if like me, you use your tumble dryer a lot. It is a sacrificial part, designed to wear out. Easy to replace simply by removing a rear plastic panel. You'll need a pair of pliers to remove the split pin and a "torx" driver to remove the retaining bolt. It helps to also remove the top cover to push the drum, but you can do it without that step if you want.

    Ease of fitting 4.0 out of 5
    Quality 5.0 out of 5
    Value 5.0 out of 5
  • North East
    5.0 out of 5

    Simple Replacement

    The bearing is easy to replace simply by removing the rear housing cover (2 screws) and the third which holds it in place ...only took a couple of minutes.

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 4.0 out of 5
See all reviews
Ask a Question

10 Questions and 12 Answers

This part has worn through on my tuble dryer - question is should there originally have been some ball bearing between the shaft and this part? I can see the sfaft of the drum does have a thinner bit where balls may have sat? Thanks

By nleather1 - - 25 July 2011
  • If the hole in the teardrop bearing has elongated towards the bottom and the dryer has recently been more noisey you may just need to change the teardrop bearing without the need to change the shaft. To check if the shaft is okay, accurately measure the bearing retaining self tapping screw hole from the centre, then mark and drill a new temporary hole for the self tapping retaining screw the same distance from the centre but 180 degrees opposite the original hole, this will enable you to rotate the bearing around 180 degrees so the elongated part is now near the top and the shaft will rest on the unworn part of the bearing. If the dryer then works with no drum noise then the shaft is okay and you just need a new teardrop bearing. By GB - - 12 November 2016
  • Can I just add that the shaft part that looks like it has had ball bearings in, actually looks like that because it has worn a groove in it because it has gone right through the bearing part itself into the casing. So you will need a new shaft also. By SimonT - - 28 November 2011
  • no this part is made to wear By Richi - Ireland - 29 July 2011
Answer this question

hello i was wondering if this fits in the square bearing bracket or is it retained by a bolt / rivet in the smaller hole ? thanks Enda

By enda - leeds - 02 August 2009
  • No. There are two types of bearing, the one pictured and the square version - they are not interchangeable. By Redbrick - Yate - 08 November 2013
  • this part fits with great ease, two screws to remove the bearing cover, then one screw through the small hole, take around five minutes to remove and fit. By ianoliver48 - scottish borders - 26 November 2009
Answer this question

I have worn out my bearing at the rear of my vtd00g. I see the bearing replacement kit and a new belt and the bearing housing, however, where does this bearing go? Thanks

By Frantic - Manchester - 30 July 2009
  • this is not a replacement for a carbon bearing, this fits on the end of the shaft. By ianoliver48 - scottish borders - 26 November 2009
  • the bearing goes on the rear back cover there is one hole were it fits through and the shaft on the rear of the drum goes in the bearing hole By gaz36 - london - 25 September 2009
Answer this question
By AWM - Oban - 04 February 2016
  • Chris from eSpares
    Chris at eSpares says...

    If this bearing has worn through the drum shaft is likely to be damaged and require replacing. If your dryer has three screw heads showing in the centre of the drum kit Stock Number: ES546701 is suitable. If there are no screws showing you will require a kit specifically for the riveted type drum shafts Stock Number: ES1672507 order the correct type for your dryer.

Answer this question
By gravy - mid wales - 30 October 2014
  • Chris from eSpares
    Chris at eSpares says...

    See the video now attached to this part. Try removing the belt of the motor and checking it rotates easily when moved by hand.

Answer this question
See all questions and answers