Tumble Dryer Polyvee Drive Belt - 1991 EPH

Stock Number: ES537769

In Stock Available for immediate despatch

Rated 4.7 out of 5 (46 customers)

Read all reviews Write a review

Main product image Enlarge icon enlarge image

Will this part fit my appliance? [?]


Tumble Dryer Polyvee Drive Belt - 1991 EPH

Is your tumble dryer's drum no longer rotating, even though the motor is running smoothly? If so, you may have snapped or worn out the drive belt. Don't panic though, eSpares could have the part to turn your luck around. This replacement drive belt can be fitted to make sure things are turning in your dryer and you're enjoying fresh, warm clothes again.


  • Type: Polyvee
  • Length: 1991 mm
  • Section: EPH
  • Note: This is a stretch belt and is extremely tight and difficult to pull into place.


Spare part for select models of Creda, Hotpoint, Indesit and Proline tumble dryers.

Please check the list of suitable models to ensure that this is the correct part for your appliance.


How to replace a tumble dryer belt

This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.

Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.

More product images

Product Reviews

Rated 4.7 out of 5 (46 customers)
Write a review
  • Good Service

    • 5.0 out of 5
    • 2.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Melksham Wilts

    The belt was delivered very quickly. I had been 'warned' that it would be difficult to fit --- and it was !!. However The belt did its its job. I would recommend E Spares.
  • Tumble dryer working again!!!!

    • 5.0 out of 5
    • 1.0 out of 5
    • 4.0 out of 5
    • 5.0 out of 5


    Thanks to your tutorial on YouTube I was able to carry out the repair successfully. The belt was very hard to get onto the pulley but lots of swearing and perseverance paid off
  • Perfect replacement

    • 5.0 out of 5
    • 4.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Birmingham

    This requires a little more stripping down than older machines and as it is a stretch belt some strength is required I also replaced drum rear bearing and pivot at the same time ( these parts failed -reason for belt renewal )

Ask & Answer

(2 Questions and 2 Answers) Ask a question
  • Q How do I get the belt on to the tension pulley wheel on my IDC85S . 1 Answer

    I purchased a new belt from you for the above mentioned condenser dryer but I cannot get it on to the pulley wheel it looks like it's far too small. I have checked if it is the correct belt on your list and it is, so I think I must be doing something wrong. I have watched lots of your help videos but you don't have one for my particular model, most of the other models seem to have a spring tension which has to be disconnected in order to get the belt in the correct position but mine has no spring. Please could you give me some advice as to how I can do this.

    By Michelle Alderman - Gillingham Kent - 27 July 2015

    • A
      This belt is a stretch belt and has to be stretched around the the tension pulley. This is very hard to stretch try passing over the spindle and leading on to the pulley then carefully turn the drum to pull it on and over the pulley.

      By Chris eSpares Staff - 27 July 2015

  • Q the model no is the same but no letter after it. The length of the belt is 1820 1 Answer

    By rosie - surrey - 01 June 2014

    • A
      In order for us to answer your question or source the exact part you require please provide us with the following information: Appliance make, model and serial number of your appliance. For further help visit the "Finding Model Numbers" page on our website here: http://www.espares.co.uk/findingmodelnumbers. Alternatively please copy and paste this link into your web browser.

      By Chris eSpares Staff - 02 June 2014