If your fan oven's element has finally given up and left you with a cold oven, eSpares can soon help you out. This genuine spare element from Electrolux could be the part to provide you with a fully functional, hot oven once again. No more takeaways necessary!
Also Known As: Circular Element, Round Element
Height: 223 (mm)
Width 190 mm
Bracket : 140 mm
Tags: 95 mm
Genuine spare part suitable for select models of AEG, Electrolux, Tricity Bendix and Zanussi ovens.
Please check the list of suitable models to ensure that this spare part will fit your appliance.
How to replace an oven element
This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.
Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.
Purchased mid afternoon and received promptly the next day (for additional next day delivery). Product had suffered minor damage (bent connector) but managed to straighten. Difficulty in getting screws out from old element but apart from that the item was easy to fit and brought my oven back to life. Very pleased.
Fan oven element replaced in minutes05 May 2015
4.0 out of 5
4.0 out of 5
5.0 out of 5
5.0 out of 5
By David B- Cambridge
Thanks to the helpful video on your website, speedy delivery and good value product, my oven is up and running again. Fitting was very straightforward - I would have done the job in 15 minutes flat had I not had to move the element securing clip about 5mm to fit the existing screw hole in the oven back plate.
Have had one before.26 April 2015
3.0 out of 5
2.0 out of 5
3.0 out of 5
3.0 out of 5
By Andy- STOCKPORT
Have bought one of these before about 5 years ago. Really easy to fit. This time it came with three brackets instead of just the one, had to cut the 2 extra brackets off to make it fit. Just be extra careful you don't break it when removing other two brackets.
QWill this stop my electrics tripping out when I turn the oven on?5 Answers
Main oven has started tripping my electrics. Grill and top oven all ok. But as soon as the main oven is turned the power trips out.
- 29 December 2008
your element has shorted to earth replace element
By handyman017- scarborough
- 12 March 2010
its the main cooker element has blown,so triping out,i had exactly the same,fitted new one now better than before
By Anonymous- ashford
- 04 March 2010
yes it should do. when an element goes it melts together and it could cause a short circuit other causes could be loose wiring on element
By Anonymous- essex
- 24 February 2010
It is possible that the main element has been damaged and it is causing an electrical short. Sometime the circular rigns fuse together and that may cause the short.
By sigmosh- London
- 23 February 2010
Without actually seeing your oven, it is impossible to tell what is causing this problem. What I would advise is talking to your local cooker specialist and they should be able to diagnose the problem for you. And that's where we come in! With thousands of oven spares, we're bound to have the part for you.
QMy oven has a top oven and a bottom oven. Which one is this element for? (I need one for the bottom oven!)4 Answers
By nyoung02- Wiltshire
- 29 April 2010
This element is for the BOTTOM OVEN of a Zanussi ZHQ575. To replace, gently unclip the thermostat from the top right hand corner of the back plate, unscrew the back plate and old element, pull the spade connectors from the element taking care that the wires don't spring back into the holes. Push the connectors on to the new element and reattach the element and backplate to the cooker. Clip the thermostat back in place. Should take no more than about half an hour.
By unclekev- Southern Ireland
- 16 February 2011
Please contact us with your full model details so that we can help you get the correct element for your appliance. Hopefully this link helps:
- 18 June 2010
normally the top oven doesnt have a fan,the only element is for the grill.you can tell if that is working ,by turnig on and see it glowing ,therefore element would be in the bottom oven.but have you checked your thermostat! my advice is do the element first ,as these normally go first,they are very easy to fit ,and dont take much time at all. hope this helps.
By bacardi1- hampshire
- 15 June 2010
This is definitely the one! You just unscrew the plate at the back and the old element, then pull the crimped wires off (this is the hardest bit - I used pliers) then reassemble.
If the lights all come on and it doesnt warm up then its definitely the element!
Have removed the old element but the clips keep popping off the new element so haven't yet screwed element in. How can I make the wire clips stay attached?
- 01 October 2013
If the clips you refer to are the spade connectors for the wires to the element it is possible to tighten these by gently squeezing the rolled end to reduce the gap. If the connectors are in poor condition they can be replaced by cutting off the old ones and obtaining new from most car spares shops.
QIt says I need top check the pnc number against the 'list of appliances' but where is the list of appliances? Could not find on the page,nor found with search..can you confirm which I need - details below...1 Answer
John Lewis oven model JLBIDOS904
Product number 944171399
Serial number 64900009
By Nigel.- Southampton
- 08 February 2012
The element you need for that model and product number is our stock code ES1007939
QArrived in no time but can unscrew the front panel :-(((1 Answer
I have tried all morning to unscrew the front panel to access the element
I have tried WD40 and a lot of it but the screw are so stuck.
Did you ever came across with this before? Do you have any suggestion?
I really want to try to save some money and do it myself
By Gianni- London
- 29 October 2011
I had a similar issue but with just 1 screw on my front panel. It has corroded into the clip at the back and in my effort to unscrew it the cross head just rounded out.
I used a dremil to cut the head of the screw into a flat so i could use a flat blade screw driver. After a bit of wigling about the screw came out and i replaced it with a new one.