Universal 2300 Watt Fan Oven Element

Stock Number: ES209572

In Stock Available for immediate despatch

Rated 4.7 out of 5 (711 customer reviews)

Read all reviews Write a review

Main product image Enlarge icon enlarge image

Will this part fit my appliance? [?]

Click on your brand to check if this part fits your appliance

Bosch Cookers & Hobs Neff Cookers & Hobs Siemens Cookers & Hobs


Fix your cooker yourself and save money! This replacement main oven element comes with two terminal tags and fits most Bosch, Neff and Siemens ovens.

  • 2300 Watts
  • Diameter: 192mm
  • Distance between terminal plate screw holes: 36mm (to the centre)

You may need a Torx head screwdriver to fit this part, depending on your model. If you haven't already got one, why not add one to your order today?

Please note: Due to new UK standards, this circular element no longer has an earth connector.

How to replace an oven element

This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.

Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.

More product images

Product Reviews

Rated 4.7 out of 5 (711 customer reviews)
Write a review
  • Great Product

    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - manchester

    This is the second one i've bought, the first one lasted two years! Very easy to fit just three wires and a few screws it took 10min's and i'm no electrician, anyone could fit one of these, have a go no need to phone a pro!
  • Painless process

    • 5.0 out of 5
    • 5.0 out of 5
    • 3.0 out of 5
    • 5.0 out of 5


    Oven (14 years old)failed to heat. Reckoned it was the element and wanted economic replacement. Took only 15 minutes to fit since I had previously replaced the fan motor and knew what to expect. It only has to last a few years to be well worth the cost.
  • Exactly what was needed

    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5
    • 5.0 out of 5

    By - Fife, Scotland

    Excellent service and help to remove old and fit new through videos.

Ask & Answer

(16 Questions and 21 Answers) Ask a question
  • Q The wire clips which connect to the element - one has arced with the old element and corroded 2 Answers

    Is there a replacement wire to connect to the element? My father is a qualified electrician and could fit it with the right part.

    By Anonymous - Cheltenham - 20 February 2011

    • A
      That is correct but ensure the "Lucar" spade terminal is not plastic coated! Always use plain connectors.

      By HarleyJon - Dorset - 27 June 2011

    • A
      They are standard spade connectors (female) can be purchased readily from DIY or motor spares outlets and crimped to the existing wire.

      By Kevo - Leicestershire - 08 March 2011

  • Q NEFF B142W2GB 2 Answers

    I have a NEFF B142W2GB, its around 3 years old. When I use the grill its ok, but when I put the oven on it runs for about 10 to 12 minuets and then it blows the 63A 30mA RCD in the consumer unit. Could it be the element.

    By ashy56 - 16 June 2010

    • A
      Please consult an engineer for support before ordering any spares because we cannot give out technical advice unfortunately.

      By eSparesMalindi eSpares Staff - 25 June 2010

    • A
      sounds like it could be - my oven element tripped the RCD when it went. Your element could be shorting only when it gets really hot and so when it trips and cools down again it is no longer a short circuit. So a new element is the likey answer but I am no expert - just a humble engineer. I bought the universal one and it is easy to fit - dont know about reliability - only had it a week.

      By OldFatMark - Hitchin - 24 June 2010

  • Q How do you remove the fixings 2 Answers

    The fixings on the terminal plate of my cooker element are different. One is a phillips self tapping screw but the other is a very slim headed bolt with a head approx 1mm thick. I cant get any purchase on this to remove it. Any ideas how to remove?

    By moraleem - 26 November 2009

    • A
      I had the same problem. It is necessary to pull the oven out, remove the screws and take off the back plate. Obviously you have switched off at the supply point. You can then get access to a nut and undo it. I replaced my element with an M4 bolt. Make sure you fit the earthing wire when you put the washer and nut back on. Good luck. I hate espares

      By PHERB4 - Leighton Buzzard - 25 February 2010

    • A
      I assume 1mm thick means the depth not the width of the head. It could be a countersunk screw. Assuming you have enough room, try using a good pair of "Mole Grips" to get the screw started. If all else fails, try tapping with a centre punch at a 60 degree tangent, and replacing the screw

      By ElectricalEngineer - 16 December 2009

  • Q Why a different watt to the genuine part? 2 Answers

    Hello. I have just ordered this part for my Neff U1422 but have just noticed that there is a difference in this and the genuine part. This item is listed as 2400w and the genuine part (which I thought would be same spec) is listed as 2300w (item ES655398). Would you please advise why there is a difference as I am not concerned about safety. Cheers.

    By Graham7687 - 17 August 2009

    • A
      Don't worry about the rating, as the voltage tolerance has changed in recent years in the UK. It may just take a few minutes longer to cook stuff.

      By Gilbod - Cambridge - 27 April 2010

    • A
      The universal versions are made to suit the majority of ovens, fitting this as a replacement for a 2300w version will not cause any issues. The oven's thermostat will control the temperature it reaches. So in my opinion nothing to worry about.

      By MartynP - Northampton - 21 January 2010

  • Q what do you do with the earth wires 2 Answers

    there are two wires for the earth terminal coming from the back of the oven what do you do with these as they might touch the live connections when replacing the element back into postion

    By fishface - st neots - 28 November 2008

    • A
      Hi There. Simply remove the spade connection for the earth connection on the element, then fit a ring type crimp on the wire, pass 1 of the fixing screws through the hole in the ring terminal & replace the fixing screw to secure the element & this will re-fix the earth in the correct position. Regards

      By Bobby9876 - 03 June 2009

    • A
      Hi Fishface Your best bet for advice fitting this is an electrician or cooker specialist. We're not electricians, we don't want to give you advice that might be dangerous!

      By Rory eSpares Staff - 02 December 2008