Washing Machine Rubber Door Seal

Stock Number: ES187324

Manufactured by Zanussi

(This part fits select models)

In Stock Available for immediate despatch

Rated 4.4 out of 5 (19 customers)

Read all reviews Write a review

Main product image Enlarge icon enlarge image

Description

Washing Machine Rubber Door Seal

If you've got a split door seal, then it's high chances your floor is going to be soaked whenever you do the washing. So, ensure the only thing coming out of the machine is clean clothes with this replacement door seal.

It's a genuine spare part for select AEG, Arthur Martin, Electrolux, Husqvarna, John Lewis, Juno, Kuppersbusch, Lloyds, Marijnen, Privileg, Rex, Rosenlew, Zanker, Zanussi and Zoppas washing machines.

As with all spare parts please check the list of appliances prior to ordering to ensure that this is the correct rubber door seal for your washing machine.

How to replace a washing machine door seal - Bosch

This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.

Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.

More product images

Product Reviews

Rated 4.4 out of 5 (19 customers)
Write a review
  • Very difficult fit

    • 5.0 out of 5
    • 1.0 out of 5
    • 5.0 out of 5
    • 3.0 out of 5

    By

    The Zanussi FJS1425W has been going well since 2001 & then started leaking from a split door seal. This seal is an excellent match to the original. Note where things are on pulling off the original seal & don't break the plastic outer ring & wait for the surprise of the inner spring. Fit the inner part of the seal first but apply washing up liquid to the grove - I struggled for 1hr with dry fitting, learnt a bit & then fitted it in 2min with the washing up liquid in situ. The next part is a nightmare - fitting the inner spring. This is much smaller in diameter than where it is going, requires lots of stretching deep inside machine & little room to get at it. Read all the other peoples entries here & they are not exaggerating & in my opinion they were softening the blow. You can not remove the front of the machine, though you can take off the lid & this gives some limited but crital access. Many attempts later I finally managed to pull the spring around the seal with a satisfying click, starting at the bottom & working up. It took the help of my wife & cut fingers & copious swearing but a very satisfying feeling. Fitting the front part of the seal with its plastic spring is easy. Not tried the machine yet but just basking in the relief of completing the impossible puzzle of getting that inner spring on.
  • Zanussi washing machine

    • 2.0 out of 5
    • 1.0 out of 5
    • 4.0 out of 5
    • 4.0 out of 5

    By - north wales

    tried follow the video instructions to fit the new door seal, but the front panel of our machine wraps around half way of each of the sides, so bit confused as to how to remove it! Will sadly have to call in the professionals but hopefully will have saved some money as the part looks exactly as expected.
  • Awful to fit on a Zanussi Jetstream 1200

    • 4.0 out of 5
    • 5.0 out of 5
    • 4.0 out of 5
    • 1.0 out of 5

    By - Watford

    Well, the video is useless for the Jetsteam, as you cannot take off the front, and here your troubles start. You have to get the seal on, and for that your hands are pushed through the door hole. Use washing up liquid to lubricate the seal so it slips into the outer drum groove. Then the spring needs to be fitted back.... You need two people, and I suggest two large, broad bladed flat screwdrivers. We started (actually, started many hours earlier, trying other, unsuccessful ways) with getting the spring fed in at the 1 o'clock position, put the blade of the screw diver such that it will stop the spring coming out, blade accross the gap, not pushed in, and get other person to hold. Feed spring around to the 5 o'clock position, ensure it is as far back as possible, and use second screwdriver in the same way (blade across gap). With the spring now held in place over about a third of the circle, you need to pull and feed it over the rest. Push it as far far back as you can, hopefully it will slip into the groove where it belongs. I found that again, a good coating of washing up liquid helped. This final approach still took 4 attempts, and 30 minutes. You will have sore fingers and knuckles, at the finish you may well have a well stretched spring pulled around the outside of your hand as you ease it over the last bit of the seal. Push it well back, and there is hopefully a rubber muffled snap as it slips into the right place! I think one of those jobs it is worth paying someone else to do, and "ease of fitting" is in no way a term I would use to give any rating to this product, though that is no fault of espares! It is an absolute......

Ask & Answer

(5 Questions and 5 Answers) Ask a question
  • Q How can I fit door seal on my Zanussi electrolux waching machine 1 Answer

    By Anonymous - 04 October 2011

    • A
      http://www.fixya.com/support/t1097749-zanussi_fjs1225w - take a look at this answer it worked for me on my zanussi which looks the same as your model - you can't get the front off the machine so it is really helpful to have someone to help hold the door seal in place on the drum as you snap it on all the way round.

      By Gillyd-s - Scotland - 12 October 2011

  • Q How to replace the rubber door Seal of my Zanussi washing Machine 1 Answer

    Hello. I would like to replace the rubber door seal of my Zanussi washing Machine (model FJS 1225W). I understand that I can get the new seal from yourselves. Any tips/ instructions on how I can do the actual change over? From what I gather, there is a plastic ring with a clip holding the seal in place. How do I remove this ring carefully, inorder to remove the old rubber seal? Any other tips? Thank you. Best regards, Aziza.

    By Aziza - 17 May 2009

    • A
      Hi Aziza, the seal for the FJS1225W is this one: http://www.espares.co.uk/part/washing-machines/zanussi/p/1085/332/0/0/187324/washing-machine-rubber-do.html

      By Rory eSpares Staff - 10 July 2009

  • Q Cannot see product for model: ZWF1437W 1 Answer

    Item required is a washing machine rubber door seal Product No. of washing machine 914522202/01

    By cherylism - 30 April 2009

    • A
      Hi Cherylism, the seal for your washing machine is this one: http://www.espares.co.uk/part/washing-machines/electrolux/p/1085/15/0/0/561731/rubber-bellow-rim-jet.html

      By Rory eSpares Staff - 10 July 2009

  • Q Will ES187324 Rubber Door Seal fit my Zanussi FJS 1197W? 1 Answer

    By Faith - 11 March 2009

    • A
      Hi Faith, the seal for your model can be found here: http://www.espares.co.uk/part/washing-machines/electrolux/p/1085/15/0/0/101456/door-gasket.html

      By Rory eSpares Staff - 01 May 2009

  • Q Cant find seal for model zwx160w 1 Answer

    rubber door seal for zannussi 1600 5.5kg

    By Anonymous - 16 January 2009

    • A
      Hi Gerryrose You can find the door seal for your model here: http://www.espares.co.uk/part/washing-machines/zanussi/zwx1605w/p/1085/332/0/539693/110878/door-gasket.html

      By Rory eSpares Staff - 18 February 2009