If your Dyson has lost suction, it might be due to a tear in internal hose. Replace it with this genuine spare from Dyson.
Please note: This short hose is located on the underside of the Dyson vacuum cleaner, not to be confused with the hose located to the rear of the cleaner.
This genuine Dyson part fits all models in the 'DC07' and 'DC14' ranges, in addition to select models in the 'DC04' range. Please see the list of compatible appliance models prior to purchase.
Other part numbers for this item: 2690023136, 904219-02
How to replace a Dyson DC04 hose
This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.
Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.
Great service - well done for excellent instruction video and cheap part service22 May 2013
5.0 out of 5
5.0 out of 5
5.0 out of 5
5.0 out of 5
By Tabbers- York
Brilliant idea to offer video and parts - I have just fitted a new hose to our vaccuum and it took less than a minute. My wife and I were going to spend quite a lot on a new vacuum but your service let me fix our old one for next to nothing - brilliant - and the email tracking of the part made sure I knew what was happening which was fab. I don't normally write reviews but your service deserves it . Thanks
Proper simple Do It Myself assembly21 May 2013
5.0 out of 5
5.0 out of 5
5.0 out of 5
5.0 out of 5
By Pen- Wellingborough
I was delighted to be able to buy and fit the Internal Hose myself rather than having to pay an Engineer. I did watch the little video first - and was delighted it was so easy
this hose was needed as the last one fell apart !!16 May 2013
5.0 out of 5
5.0 out of 5
5.0 out of 5
5.0 out of 5
By bromhead- Tees-side
it was easy to fit, the price was 'right', and now the vacuum almost pulls the carpets up !!. excellent value, and I would recommend this seller to anybody.
i have looked at my dyson and I can't see how to get the hose off of the machine. Please can you advise me on how to fit this. Thanks
By Ness
- 09 October 2009
A
Haven't you had an answer yet, Ness? Grip one end, twist until it moves, then pull. Then the same at the other end.
By priorypete- Sussex
- 29 April 2010
A
you have to take bottom cover off the brush there are three plastic half turn bolts then push drive belt off at the motor shaft pull brush out with belt,pull brush cover with hose assembly out ,unscrew hose off screw new one on, put drive belt back on motor shaft ,refit brush cover and pull belt back though it, pull belt so you can push brush though it, re fit the brush,refit the bottom cover
By JOHNWITHDOT- lincolnshire
- 24 April 2010
A
Take the plate off the bottom. Use coin to turn screws. Prise off old hose where the push fit is, and unscrewother end. Replace push fit. In theorey you line up the plastic screwtube threads, and twist. One end of the pipe is a left hand thread, the other RH. In practice you need to juggle, but it will fit and screw home eventually. Then put everthing else back.
Required for another application. ( Bissel carpet washer)
By bramley60- Homecounties
- 20 November 2009
A
We do not usually put up measurements as our parts are model specific. This part is made specifically for the Dyson models listed above. Please check your model details to make sure you get the correct parts. The following link may help you:
http://www.espares.co.uk/findingmodelnumbers.aspx
Your basket is empty.
enlarge image
- 09 June 2010