Washers & Dryers
Vacuums & Floorcare
TV & Audio
Home & Lighting
In the unlikely event that you find this product cheaper elsewhere online, we'll refund the difference. Full details of the guarantee are available here
Stock Number: ES1136941
Manufactured by Flymo
Available for immediate despatch
Read all reviews
Write a review
Click on your brand to see the model numbers this part fits.
Has your lawnmower's switch been letting you down? This is an essential bit to have on your mower, without it your machine is rendered useless. Replace it with this cost effective, 8 Amp, 250 Volt spare from Flymo.
Please note: The switch housing is not included, but can be purchased separately.
This is a genuine Flymo spare part that has been made to fit the select lawnmowers and lawnrake. Please check the list of appliances before purchase to ensure that this is the right part for your appliance.
This video should help with fitting this part. However, the exact layout and fitting technique may differ for your make and model.
Be safe - always unplug any appliance from the electricity supply before carrying out any work on it.
If you are in any doubt contact a qualified repairer.
- Fix-It Expert
Easy to fit,instructions provided; saved cost of new mower
- Fix-It Beginner
excellent value and delivery very prompt.No problem fitting same and worked a treat.
- Newtownabbey, Co. Antrim
- Fix-It Expert
Super purchase. Easily fitted. Others complain about hard to release push in wires, SIMPLE open up the old switch, after all its scrap! Release spring pressure and out they pop. Recomended.
Turbo Compact Vision 330
- 25 March 2010
Actually I found the best way to remove the two wires was to prise the back off the switch (doesn't matter if you wreck it). It is then a simple matter of removing the clips securing the wires and pulling them out intact. This way, there is no danger of damaging the solder tags on the ends of the wires, which are useful when refitting. To refit, simply push the wires into the appropriate holes in the new switch and they will latch. Same for the capacitor.
- 23 April 2013
The way I removed the wire from the old switch was to push a pin into the hole beside the wire and pull. The wires are held inside the switch by a simple spring mechanism!
- 02 June 2010
on the new switch it has two scews for the power wires,but only four holes with metal behind two for the capacitor whic I managed to put in but it is impossible to push in the two black wires from the mower plug.
- 09 February 2011
Hi again reetpetite, the four holes without screws have a clasp mechanism inside them; the wires from the mower plug retainer pin should slot in and fix in to place. If they don't, the switch might be defective.
- 15 February 2011
- 08 February 2011
Hi there, to wire in the new switch, simply loosen the two screws, put the wires in the corresponding holes, and tighten the screws back up.
- 09 February 2011
Would I need to purchase the lower and upper housing for this part or is it included?
- 19 October 2009
The part listed is just the switch, you will need to individually buy the other parts.
- 03 February 2010
Flymo pac a mow model 9643305-01. Does the 8A 250v switch inlcude the capacitor (flymo part no 514 83 97-01) and lead assembly please.? I need to replace the complete switch assembly as one piece. ?
- 09 August 2009
The capacitor and lead assembly are sold as seperate parts for this lawnmower. These are the stock numbers for both parts:
- 03 June 2010
Get special offers and the latest repair tips
Everything you ever wanted to
know about eSpares.
Calls are charged at 5p per min from BT landlines, other networks and mobiles may vary.
Copyright © eSpares LTD. All rights reserved 2004-2013.